CCNA

1. Cisco Network Support Certifications 2. Networking Terms 3. INTRODUCTION TO NETWORKING 4. TYPES OF NETWORK 5. The Development of the Internet 6. NETWORK ARCHITECTURE 7. TOPOLOGY 8. BUS TOPOLOGY 9. RING TOPOLOGY 10. STAR TOPOLOGY 11. MESH TOPOLOGY 12. HYBRID TOPOLOGY 13. Speed of Networking device 14. NETWORK DEVICES 15. Exploring Wireless Network 16. REPEATERS 17. HUB 18. SWITCH 19. BRIDGE 20. ROUTERS 21. TRANSMISSION Telecommunication 22. Difference between Full Duplex, Half Duplex and Simplex 23. IP-ADDRESSING and IPV4 24. IPv4 address classes 25. IPV6 [ Internet Protocol Version 6 ] 26. SPEED OF VARIOUS DEVICES 27. Network Security 28. Some basic suggestion and steps to prevent Attacks and Network security 29. OSI model 30. UPPER and LOWER Layer 31. Application Layer (Layer 7) 32. Presentation Layer (Layer 6) 33. Session Layer (Layer 5) 34. Transport Layer (Layer 4) 35. Network Layer (Layer 3) 36. Data Link Layer 2 37. Physical Layer 1 38. TCP/IP The DoD Model 39. ROUTED PROTOCOL 40. Ports and Application 41. Important Application, Protocol and Port Number 42. Router Function 43. Types of Routing Protocols 44. STARTING ROUTER 45. CISCO IOS 46. Logging in to the Router 47. CISCO Router IOS commands List 48. Setting time and date of router 49. Router configuration commands 50. Optimizing Switch and Router 51. Understanding Router Terms 52. ROUTER SECURITY 53. Configuring CISCO SWITCH Security Policy 54. IMPLEMENTING STATIC ROUTING 55. UNDERSTANDING THE NEED FOR NAT 56. WAN Connections 57. Access List [ACL] 58. VLAN [Virtual Local Area Network] 59. SPANNING TREE :- BROADCAST STORM 60. Lab 1 Setting up a Serial Interface 61. Lab 2 : IP Addressing 62. Lab 3 Static Routes 63. Lab 4 Default Routes 64. Lab 5 RIP Routes 65. Lab 6 IGRP Routes 66. Lab 7 EIGRP Routes 67. Lab 8 OSPF Routes 68. Lab 9 CHAP and RIP 69. Lab 10 Standard Access-Lists with RIP 70. Lab 11 Extended Access-Lists with RIP 71. Lab 12 Static NAT 72. Lab 13 Many to One NAT 73. Lab 14 NAT Pool 74. Lab 15 ( 2950 Trunk ) 75. Lab 16 ( 2950 Trunk Dynamic ) 76. Lab 17 (2950 VLANs) 77. Lab 18 ( 2950 Deleting VLANs ) 78. Lab 19 ( 2950 VTP ) 79. Lab 20 ( 2950 VTP w/ client ) 80. Lab 21 ( 2950 Telnet )
Pr.Pg Next Pg

CISCO IOS tutorials

  • CISCO IOS is the internetwork Operating System. It’s a operating System of Cisco.

  • It is a command line method of configuring a CISCO Device

  • CISCO IOS software is consistant through nearly all over CISCO devices.

  • Learn IT once and use it many times.

  • It is more powerful than any Graphic Interface.

  • There are 3 methods to connect routers given as follow

 

1) Connecting to the Cisco Router via CONSOLE port

  • Get a Console Cable. On one side we have RJ-45 connector and other side we have 9 pin Serial female connector that get connected to PCs COM1 Port.

  • Connect RJ-45 connector to Router “CONSOLE” port and other end of cable to PCs COM1 or Com2 port. Most Computer will be using COM1 port.

  • Start PC and Router.

  • On PC click on “Start :- All Program :- Accessories :- Communication :- Hyper Terminal”

  • It will ask New Connection name for Hyper Terminal Session. Give appropriate name.

  • It will automatically display COM1 or COM2, click on configure and set following values

 

Bits Per Second 9600

Data Bits 8

Parity None

Stop Bits 1

Flow Control None

 

2) Making VTY (Virtual Terminal Connection) via CONSOLE

  • Once you have configured Router using Console port locally, you can connect it remotely over Ethernet and Switch. And for this you do not have to be physically close to router. To connect it using telnet you must configure following things first via console port i.e.

  • Configure and enable router Ethernet interface with proper IP address

  • Set the enable secret password

 

On PC click on “Start :- All Program :- Accessories :- Communication :- Hyper Terminal”

It will ask New Connection name for Hyper Terminal Session. Give appropriate name.

From connect using select “TCP/IP (Winsock)”

Enter host address is of Router for e.g. 192.168.1.1

Port Address “23”

 

3) Making VTY (Virtual Terminal Connection) via TELNET

  • Once you have configured Router using Console port locally, you can connect it remotely over Ethernet and Switch. And for this you do not have to be physically close to router. To connect it using telnet you must configure following things first via console port i.e.

  • Configure and enable router Ethernet interface with proper IP address

  • Set the enable secret password

Go to start - run - telnet <IP address> for e.g. telnet 192.168.1.1


Pr.Pg border                                              Next Pg