Windows 7

1. Microsoft Windows 7 tutorials 2. Module 1- Installation, Upgrading, and Migrating to Windows 7 tutorials 3. Editions of Windows 7 tutorials 4. Hardware Requirements for Installing Windows 7 tutorials 5. You can install Windows 7 in following different ways, including: 6. Consideration for Upgrading v/s Migrating tutorials 7. What is Migration tutorials 8. Migrating User Data and Settings tutorials 9. Performing an Image-Based Installation of Windows 7 tutorials 10.Configuring Disks and Device Drivers tutorials 11. Partitioning Disks in Windows 7 tutorials 12.GUID - GPT Disk tutorials 13.Disk Management tools tutorials 14. Simple Volume tutorials 15. Spanned and Striped Volumes tutorials 16. Maintaining Disks, Partitions, and Volumes tutorials 17. Disk Quota tutorials 18.Working with VHD Virtual Hard Disk tutorials 19. Device Driver in Windows 7 tutorials 20.System Restore tutorials 21.LAST KNOWN GOOD CONFIGURATION tutorials 22.Configure and Trouble shoot Network Connections tutorials 23.What is an IPv4 Address tutorials 24. Note - IPV4 25. IPv4 address classes tutorials 26.Default Gateway tutorials 27.Public and Private IPv4 Address tutorials 28.IPv6 Network Connectivity tutorials 29.IPv6 UNICAST ADDRESSES tutorials 30. IPv4 Address can be assigned by following types tutorials 31.Implementing Name Resolution tutorials 32. Trouble Shooting Network Connectivity tutorials 33. Implementing Wireless Security tutorials 34.Wireless network Technologies tutorials 35.What is Wireless Broadband tutorials 36.IEEE 802.11 tutorials 37.Wireless Network Configuration tutorials 38. Security Types tutorials 39. Implementing Network Security tutorials 40.Configuring Windows Firewall tutorials 41.Ports and Application tutorials 42.Important Application, Protocol and Port Number tutorials 43.Configure Inbound and Outbound Rules tutorials 44. Securing Network traffic tutorials

Simple Volume tutorials

  • A simple volume is available on a single hard-disk drive.

  • There is no Fault Tolerance that is any physical disk failure results in data loss.

  • However loss is limited to the failed disk drive only.

  • Volume input/output (I/O) performance depends upon Disk I/O speed.

  • A simple volume may provide better performance over striped Set Volume.

 

  • Note :- Most pre-installed desktop and laptop are made available using Single Simple Volume. This is for the one who require simplicity and ease of use.

  • It is advisable the business user should configure computer having one disk with more than one volume let's say 3 Volumes. That is Operating System on the First Volume, the second Volume for future new Operating system and Separate third volume for business and personal Data.

 

Exercise : Create Partition, format it and apply volume name using Diskmgmt

  1. Open the Start Screen.

  2. Type diskmgmt.msc, and then press Enter.

  3. Right-click the unallocated space on Disk, and then click New Simple Volume.

  4. In the New Simple Volume Wizard, on the Welcome to the New Simple Volume Wizard page, click Next.

  5. On the Specify Volume Size page, change the Simple volume size in MB value to 10000, and then click Next.

  6. On the Assign Drive Letter or Path page, click Next.

  7. On the Format Partition page, in the Volume label text box, type Simple1, and then click Next.

  8. On the Completing the New Simple Volume Wizard page, click Finish.

  9. When the New Simple Volume Wizard is complete, close Disk Management.

 

Exercise : Create Partition format it and apply volume name using DiskPart

  1. Open the Start Screen, type c, and in the Apps search screen click Command Prompt.

  2. At the command prompt, type Diskpart, and then press Enter.

  3. At the DISKPART> prompt type select disk 3, and then press Enter.

  4. At the DISKPART> prompt, type create partition primary size=10000, and then press Enter.

  5. At the DISKPART> prompt, type list partition and then press Enter.

  6. At the DISKPART> prompt, type select partition 2, and then press Enter.

  7. At the DISKPART> prompt, type format fs=ntfs label=Simple2 quick, and then press Enter.

  8. At the DISKPART> prompt, type Assign and then press Enter.

  9. Close all open windows.

  10. Click the Windows Explorer icon on the task bar.

  11. In the Libraries window, click Computer, and then verify the visibility of the volumes that you created.

  12. Close the Windows Explorer window.

 

 


 

border